
Tiny's LEDs RealPit VTX Power Switch
Tiny's LEDs RealPit VTX Power Switch
RealPit
Features / Uses:
- Plug in your VTx at any time with 0 power start-up
- (Not Available with FlightOne at current time)
- Turn off your VTx on the line to avoid heat buildup
- Fast Team Race Pit stops (Sub second transitions possible)
- Compatible with all major VTxs
- Turn off VTx during races to test hover builds without interfering with other pilots in the air.
- Turn off VTx after Crash for clean video for other racers.
- Solo Endurance Races, 3 quads ready on the line. Practice for more than 1 pack without taking off goggles. (Instructions on how to setup on OpenTX / Spektrum Coming soon)
- LED Indicator light on board. (Light On \ Power On)
- Can be used on any pad on Flight Controller.
- Does not need a full UART.
- I.E.: SmartAudio/Tramp on TX and RX for RealPit PinIO
- Up to 4 RealPits per quad. This opens the possibility for LEDs, and VTX, and any other device you can imagine.
- Toggle LED Power or any other devices under 1 amp draw.
Currently Supported Software:
- Betaflight (PinIO 3.3.x or Greater)
- Butterflight (PinIO)
- FlightOne 1.2.x + (VTXPRWTOGGLE)
Operating Voltage: 5V - 28V (HV-6s) 1Amp Switch
Dimensions: 10 x 12.5 x 2.5 mm
Weight: 0.5 Grams w/ Heatshrink
Demo Video ( Team EMAX Team Race):
Contents:
- 1x Realpit
- 1x 1/2" Heat shrink piece
Betaflight Settings:
In CLI:
Type RESOURCE
Locate UART TX/RX pad resource ID you are using. We wired to RX4 in this demo. RX4 is A01 Note the name of resource and ID.
Next we need to assign the Resource ID to the Custom Mode switch. Using the Resource ID from above. "A01"
resource PINIO 2 [resource=I.E=A04]
resource PINIO 3 [resource=I.E=A05]
resource PINIO 4 [resource=I.E=A06]
Type SAVE in CLI and then press enter. Your FC will reboot after applying changes.
Now go to Modes and Assign an AUX channel to the USER1 mode. Just like an arm or turtle mode switch. Click SAVE.
Now flip the switch and test. A RED LED will be lit on RealPit if your are providing power.
FlightOne Settings:
3. In Setup Tab:
- At the current time you must use Firmware version 1.2.x or greater to enable "vtxpwrtoggle" commands. This is available on FlightOne Discord. flightone.com/discord and website at FlightOne.us
- Wire RealPit VTX + to VTX Positive pad and BATT+ to Battery Source (5v-28v)
- Wire FC pad to Buzzer + pad on FlightOne FC. Then Wire GND pad to Buzzer - pad on FlightOne FC
4. Use Switch to Power VTX on and off.
- Setup VTXPWRTOGGLE switch.
- Notes: FlightOne Does not support ZERO power on. VTX will blip for a micro second prior to turning back off.
Wiring Diagram Instructions:
__________________________________________________________________________
Why buy from AirBlade UAV:
- Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
- Top Notch Customer Support: We put our customers’ interest ahead.
- Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
- High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
- Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
- Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.
Shipping Weight: 10g