Skip to content
VACATION NOTICE: SHIPPING SUSPENDED BETWEEN MAY 7-JUNE 18. DISCOUNT CODE AVAILABLE!
VACATION NOTICE: SHIPPING SUSPENDED BETWEEN MAY 7-JUNE 18. DISCOUNT CODE AVAILABLE!

Matek Sys Flight Controller H743-Wing V2

Sold out
USD $80.00

 Matek Sys Flight Controller H743-Wing V2 

Matek Sys H743-Wing V2 is the premier, INAV-capable flight controller made specifically for FPV fixed-wing aircraft. Loaded with a suite of features and tons of room for peripherals, this board lets you choose how you want to fly. 

If you're looking for a cheaper version with slightly lower specifications, check out the smaller brother Matek F411-WSE flight controller.


FC Specifications

  • MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM42605 (SPI4)
  • Baro: Infineon DPS310 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card slot (SDIO)
  • 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
  • 13x PWM outputs(including “LED” pad)
  • 2x I2C
  • 1x CAN
  • 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 1x SPI3 breakout
  • USB/Beep Extender with Type-C(USB2.0)
  • Dual Camera Inputs switch
  • 5V/9V(12V) for Camera/VTX power switch
  • High-precision Current Sense (90A continuous, 220A peak)
  • Battery Voltage Sensor: 1K:10K (Scale 1100 in INAV,  BATT_VOLT_MULT 11.0 in ArduPilot)
  • ADC VB2 voltage divider: 1K:20K
  • ADC AirSpeed voltage divider: 20K:20K
  • Static power 160mA@5V

FC Firmware

  • ArduPilot(ChiBiOS): MATEKH743
  • INAV: MATEKH743

PDB

  • Input voltage range: 8~36V (3~8S LiPo) w/TVS protection
  • 2x ESC power pads
  • Current Senor: 220A,  3.3V ADC  (Scale 150 in INAV,  66.7 A/V in ArduPilot)
  • Sense resistor: 90A continuous, 220A peak.

BEC 5V output

  • Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
  • Output 5.15  +/- 0.1V DC
  • Continuous current 2 Amps,  3A Peak

BEC 9V /12V output

  • Designed for Video Transmitter, Camera, Gimbal ect.
  • Continuous current 2 Amps,  3A Peak
  • 12V option with Jumper pad

BEC Vx output

  • Designed for Servos
  • Voltage adjustable, 5V Default, 6V or 7.2V via jumper
  • Continuous current 8 Amps,  10A Peak

BEC 3.3V output

  • Linear Regulator
  • Continuous current: 200mA

Physical

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 54 x 36 x 13 mm
  • Weight: 30g with USB extender

 

Tips and Notes

What is new on the H743-Wing V2

  1. Use ICM42605 instead of ICM20602
  2. Moved PDB/current sensor from FC board to bottom plate.
  3. Moved 8A BEC from top board to bottom plate.
  4. JST-GH connector for CAN port instead of JST-SH connector.
  5. Add a JST-GH connector for I2C2, for plug and play with ASPD-4525

ArduPilot

  • H743-WING-V2 with ICM42605 is supported by ArduPilot 4.1 latest or newer,
  • ICM42605 is defined as first IMU (IMU0) ,  MPU6000 is the 2nd (IMU1).
  • with ArduPilot 4.1 or higher, set INS_ENABLE_MASK to 7 or default 127.
  • Current sensor range is 220A on H743-WING-V2,  make sure you set the BATT_AMP_PERVLT to 66.7
  • It is recommended to use STM32CubeProgrammer to erase MCU and upload firmware.  check this blog http://www.mateksys.com/?p=6905
  • Known issue and solution,  H7 will not initialize with Ardupilot firmware

INAV

  • Current sensor range is 220A on H743-WING-V2,  make sure you set the Current Meter Scale to 150
  • IMU ICM42605 is supported by INAV3.0.2 or higher.
  • MPU6000 is the first IMU(IMU0, default), ICM42605 is the 3rd IMU (IMU2) in INAV MATEKH743 target.
  • If you want to try the new ICM-4 series of IMUs.  download inav_3.0.2_MATEKH743.hex
    • set gyro_to_use = 2
    • set acc_hardware = icm42605
    • save
  • If you stick with MPU6000 only,  H743-WING-V2 works with stable version 3.0.x downloaded from configurator also.
  • SD card and MSC mode for H743 were not implemented in INAV3.x.  They are supported by INAV4.x or higher.

Others

  • If the ESCs you are using don’t have enough capacitors integrated,  low ESR electrolytic capacitor is required for reducing ESC noise.

Including

  • 1x H743-WING
  • 1x USB(Type-C)/Beep (Passive buzzer) Extender
  • 1x 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
  • 2x 20cm JST-GH-4P to JST-GH-4P cable for CAN & I2C port
  • 1x Rubycon ZLH 35V 470uF capacitor
  • Dupont 2.54 pins  (Board is shipped unsoldered)

 

__________________________________________________________________________

Why buy from AirBlade UAV:

  • Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
  • Top Notch Customer Support: We put our customers’ interest ahead.
  • Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
  • High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
  • Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
  • Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.  

 

 

Shipping Weight: 50g