Skip to content
VACATION NOTICE: SHIPPING SUSPENDED BETWEEN MAY 7-JUNE 18. DISCOUNT CODE AVAILABLE!
VACATION NOTICE: SHIPPING SUSPENDED BETWEEN MAY 7-JUNE 18. DISCOUNT CODE AVAILABLE!

Matek Flight Controller F405-STD

USD $42.99

 Matek F4 Flight Controller F405-STD

If you want a simple flight controller that just works, this is it. The Matek F405-STD edition has 5 built-in UART that you can use to connect VTX, RX and other peripheral. The built-in barometer allows the flight controller to sense altitude real time.

 

Specifications

  • MCU: 168MHz STM32F405RGT6
  • IMU: 32K ICM20602 gyro/accelerometer (SPI)
  • Baro: BMP280 (I2C)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Blackbox: MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • Built in inverter for SBUS input (UART2-RX)
  • PPM/UART Shared: UART2-RX
  • SoftSerial on TX2, S5 or S6 optional
  • Camera control on S6 or DAC optional
  • Smartaudio & Tramp VTX protocol supported
  • Battery Voltage Sensor: 1:10
  • Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
  • BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)
  • LDO 3.3V: Max.300mA
  • I2C1 SDA & SCL: Yes
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 6x PWM / DShot outputs without conflict
  • 2x 2812LED outputs option
  • 5x UARTs
  • 1x Group of 5V/G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x pair I2C1 pads
  • 1x Side-press button for BOOT(DFU) mode
  • 1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection
  • 36x36mm PCB with 30.5mm mounting holes
  • w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
  • w/ 4pcs M3 Anti-vibration Standoffs

     Tips and notes:

    • CLI “defaults” after reflashing
    • Rubber anti-vibration standoffs are necessary to avoid the vibration woes.
    • Put a piece of sponge on the barometer to reduce the impact of airflow.
    • If you are using 5V VTX, Pls power the VTX via the 5V pad on FCHUB.  The ribbon cable can’t bear heavy current.
    • BF/  2812LED_Strip share I2C1_SCL pad as default.  either enable LED_Strip, or enable Baro.
    • BF/  2812LED can be resourced to S7 (PB8) if using Baro the same time with BF firmware
    • INAV/  Softserial_TX1 is on TX4 pad & Softserial_TX2 is on TX2 pad if CPU based serial port is enabled since 2.0.1
    • We have replaced BMP280 with DPS310 in some batches of production.
    • If barometer on your flight controller don’t work by default after flashing it with Betaflight,  Pls click “firmwares” button to check out customized Betaflight 4.2.x and tips.
    • With ArduPilot firmware, you might use the onboard DPS310 as external barometer,  set BARO_EXT_BUS ->0,   GND_PROBE_EXT ->64, save and reboot F405-STD.

    __________________________________________________________________________

    Why buy from AirBlade UAV:

    • Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
    • Top Notch Customer Support: We put our customers’ interest ahead.
    • Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
    • High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
    • Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
    • Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.  

     

     

    Shipping Weight: 30g