Skip to content

Heli-Nation Talon F7 and Gigawatt 20x20 Combo

Sold out
USD $93.00

Get this 20x20 flight stack combo for your FPV racing quads


  • 1x Heli Nation Talon F7 Flight Controller
  • 1x Heli Nation Gigawatt 35A 6S ESC


Heli Nation Talon F7 Flight Controller 

A new generation of Talon is here, now comes with Blackbox (BB) for your convenience. With a F7 processor and 8S capable, Talon is the only 20x20 flight controller on the market with a STM32F722RET6 216MHz processor.  Built in Betaflight OSD, 6 UARTS, and dedicated LDOs for cleaner gyro and OSD signals makes TalonF7 the most powerful 20X20 FC on the market. One of the features Talon F4 customers praised is the choice of using the 8 pin harness or direct soldering motor ports to the ESC. We’ve kept that option, while still adding more features, by letting customers remove the plastic connector to reveal motor ports. Now includes 3 harness cables for direct pin to Aikon AK32PIN, Spedix GS25A, and Airbot Ori32.

Albert Kim did a review on the Heli Nation Talon F7 (non blackbox) flight controller 



  • MCU: STM32F722RET6 216MHz
  • 6-Axis ICM20602 32K
  • Built in Betaflight OSD
  • Up to 8S (36V) direct battery power
  • Buzzer pads for external buzzer
  • Build in voltage monitoring resistor
  • 5V 2A BEC
  • 16MB Blackbox
  • Dedicated LDO for gyro for cleaner gyro signal
  • Dedicated LDO for OSD for cleaner OSD signal
  • Led strip shares 5V with 5V/2A BEC
  • Built in camera control pin with resistor and capacitor
  • 4 Full UARTS with RX/TX pins
  • Logical pin layout for cleanest build possible
  • 8 pin 4 IN 1 ESC plug (Direct solder motor ports underneath)
  • Remap able LED pad for additional motor output
  • TX3 & RX3 can be used for I2C for external compass
  • 5V or 3.3V selectable receiver power
  • 5V, VBAT selectable VTX and CAM power
  • Includes * 3 pin connector harness cables for direct pin to Aikon AK32PIN, Spedix GS25A, and Airbot Ori32, 8 grommets, M3 to M2 nut adapters, M3X5 standoffs
  • Betaflight Target: CLRACINGF7


  • The included Aikon harness is for the Aikon AK32 30X30 ESC. This was a mistake by us (Heli Nation) and we are very sorry. Please re-pin for the 20X20 Aikon AK32PIN as pictured below.
  • If there is a delay in startup for the CLF7 target, type the commands below in the CLI

resource i2c_sda 2 none
resource i2c_scl 2 none

  • WARNING! If you remove the JST connector to direct solder, the pinout is not the same as the JST connector. Please use the diagram below to see the correct pinout. Please pay attention to VBAT and Ground!

 Heli Nation Talon F7 20x20

 Heli Nation F7 Talon Flight Controller


  • For Talon F7 with Black Box please set your voltage scale to 81 for it to work properly 

Heli Nation Talon F7 BB 20x20 -10


Heli Nation Gigawatt 6S 35A ESC

Looking for the perfect 6S companion for your Talon FC? Good news! The Talon Gigawatt has arrived! 

The Talon Gigawatt 4-in-1 35A 6S is a new generation ESC that uses a variety of bleeding edge technologies in hardware and firmware. The Talon Gigawatt is worth your investment.
Started just less than 2 years ago, 20x20 sized electronics have progressed considerably, and this Heli Nation Gigawatt ESC is not an exception. Despite having a 20x20 footprint, it is rated up to 6S 35A constant, 45A burst which is enough headroom even for 5 inch mini quad builds. This ESC is made to be plug and play with the Talon F4 and Talon F7 line of flight controllers, however, you can use it with any flight controller of your choice.  


  • BLHeli_32 code base
  • Programmable PWM frequency of up to 48KHz
  • Auto-timing for higher efficiency and reliability
  • Analog Voltage/Current sensing
  • Adjustable “Brake on Stop” force
  • Improve direction change in Bidirectional mode
  • One current sensor to measure the total amp draw and telemetry functions.
  • ESC Telemetry (Voltage and RPMs and current)
  • Configuring from FC using DShot commands
  • Programmable sine modulation mode
  • Programmable soft bidirectional mode
  • Programmable autonomous periodic (every 32ms) telemetry mode
  • Hardware noise filter on the signal input


  • Rating: 2S-6S
  • Constant Current: 35A
  • Burst Current: 45A
  • Mounting hole: 20x20mm
  • Firmware: BLHeli_32
  • Bootloader: Yes
  • Weight (with wires): 10g
  • Signal wire length: 100mm
  • Battery lead length: 100mm


      Why buy from AirBlade UAV:

      • Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
      • Top Notch Customer Support: We put our customers’ interest ahead.
      • Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
      • High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
      • Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
      • Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.



      Shipping Weight: 60g