Skip to content

Heli Nation Talon F7 20x20 Flight Controller with Blackbox

Sold out
USD $32.99

 Heli Nation Talon F7 BB 20x20 Flight Controller

 

A new generation of Talon is here, now comes with Blackbox (BB) for your convenience. With a F7 processor and 8S capable, Talon is the only 20x20 flight controller on the market with a STM32F722RET6 216MHz processor.  Built in Betaflight OSD, 6 UARTS, and dedicated LDOs for cleaner gyro and OSD signals makes Talon F7 the most powerful 20X20 FC on the market. One of the features Talon F4 customers praised is the choice of using the 8 pin harness or direct soldering motor ports to the ESC. We’ve kept that option, while still adding more features, by letting customers remove the plastic connector to reveal motor ports. Now includes 3 harness cables for direct pin to Aikon AK32PIN, Spedix GS25A, and Airbot Ori32.

This F7 flight controller pairs well with the Aikon AK32 4in1 35A 6S 20x20 ESC that we also carry. In our opinion, this combo makes the best 20x20 flight stack on the market. It can do up to 6S while maintaining a small footprint. If you're looking for other options, Spedix GS25A and Airbot Ori32 work too. 

 Albert Kim did a review on the Heli Nation Talon F7 (non blackbox) flight controller 

Features

  • MCU: STM32F722RET6 216MHz
  • 6-Axis ICM20602 32K
  • Built in Betaflight OSD
  • Up to 8S (36V) direct battery power
  • Buzzer pads for external buzzer
  • Build in voltage monitoring resistor
  • 5V 2A BEC
  • 16MB Blackbox
  • Dedicated LDO for gyro for cleaner gyro signal
  • Dedicated LDO for OSD for cleaner OSD signal
  • Led strip shares 5V with 5V/2A BEC
  • 6 UARTS: UART1, UART2, UART3, UART4, UART5, UART6
  • Built in camera control pin with resistor and capacitor
  • 4 Full UARTS with RX/TX pins
  • Logical pin layout for cleanest build possible
  • 8 pin 4 IN 1 ESC plug (Direct solder motor ports underneath)
  • Remap able LED pad for additional motor output
  • TX3 & RX3 can be used for I2C for external compass
  • 5V or 3.3V selectable receiver power
  • 5V, VBAT selectable VTX and CAM power
  • Includes * 3 pin connector harness cables for direct pin to Aikon AK32PIN, Spedix GS25A, and Airbot Ori32, 8 grommets, M3 to M2 nut adapters, M3X5 standoffs
  • Betaflight Target: CLRACINGF7

NOTES

  • The included Aikon harness is for the Aikon AK32 30X30 ESC. This was a mistake by us (Heli Nation) and we are very sorry. Please re-pin for the 20X20 Aikon AK32PIN as pictured below.
  • If there is a delay in startup for the CLF7 target, type the commands below in the CLI

resource i2c_sda 2 none
resource i2c_scl 2 none
save

  • WARNING! If you remove the JST connector to direct solder, the pinout is not the same as the JST connector. Please use the diagram below to see the correct pinout. Please pay attention to VBAT and Ground!

 Heli Nation Talon F7 20x20

 Heli Nation F7 Talon Flight Controller

 

  • For Talon F7 with Black Box please set your voltage scale to 81 for it to work properly 

Heli Nation Talon F7 BB 20x20 -10

 

Includes

  • Pin connectors (Aikon AK32, Spedix GS25 and Airbot Ori32 compatible)
  • 8 grommets
  • M3 to M2 nut adapters
  • M3x5 standoffs

 __________________________________________________________________________

Why buy from AirBlade UAV:

  • Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
  • Top Notch Customer Support: We put our customers’ interest ahead.
  • Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
  • High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
  • Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
  • Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.

 

 

Shipping Weight: 40g