Skip to content
PLEASE BE ADVISED THERE MAY BE DELAYS WITH USPS AND CANADA POST DURING THE BUSY BLACK FRIDAY SEASON
PLEASE BE ADVISED THERE MAY BE DELAYS WITH USPS AND CANADA POST DURING THE BUSY BLACK FRIDAY SEASON

Pyrodrone Hyperlite F4 OSD V2

Sold out
USD $32.99

One of the most popular FC is back and better than ever, combining an industry favorite layout with new feature sets for freestyle, long-range, and racers. Finally, a board for every pilot!  

 
The new Hyperlite F4 OSD takes the same celebrated flat-bottomed layout (crucial for clean and tight builds) and adds a much appreciated OSD and SIX UART ports (more than any other board on the market!) for GPS, RX, SmartAudio, and even Camera Control.  
 
And with more features, comes improved ease of use with a built in 4-in-1 ESC socket and included harnesses for HobbyWing 45Amp G2, Aikon AK32, and Spedix GS35 4in1 ESCs. The built in solder pads mirror the 4in1 pad layout, so you can easily connect ANY ESC to this board to get features like current sensing and ESC telemetry (for the BL32 guys). 
 
 
PLEASE NOTE: The Hyperlite F4 OSD uses its own BF target .bin, PYRODRONEF4. 
 

Specifications:

  • MPU6000 Gyro
  • STM32F405 CPUE @ 168mhz, can be overclocked
  • 2-6S direct battery input 
  • 3.3V 100ma, 5V 1.2A BEC
  • 5V Camera Power
  • Built in configurable Betaflight OSD
  • Flat bottom PCB for SUPER CLEAN builds
  • 36x36 PCB with 30.5x30.5 mounting holes
  • 6 UARTS
    • UART1 (INVERTER FOR SBUS),
    • UART2 (FREE),
    • UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off 
    • UART4 (Free),
    • UART5 (Smart Audio)
    • UART6 (Free)
  • Built in 4 IN 1 ESC socket (Including ESC telemetry, External current sensor)
  • Plug and plug with the most popular 4-in-1 ESCs (HobbyWing, Airbot, Spedix, Aikon), with supplied cables
  • Built in solder pads mirror of the 4-in-1 ESC socket
  • Printed layout instructions ON the board - no need for instructions!

 

Version 2.3 Update:
Attention! you have to update your FW 3.5.5 or up for the VTX pit mode.
The Pyrodrone F4 OSD has a new feature!
VTX Pit mode compatibilty.

Now there are sellector pads for your VTX voltage input!
5V and VBAT.
First please jump the correct side pads according to the VTX you are using. 

And then jump the two pads on the "PIT" side ( If this feature is not needed then just jump the pads of the "ON" side and your VTX will always be on)
After you jump the PIT pads connect to Betaflight and go to CLI page , type in the following commands:

resource PINIO 1 A15
set pinio_box = 39,0,0,0
type "save" and then hit enter.

Wait for the FC to reboot, then go to the "MODES" tab in Betaflight and set VTX PIT MODE to an AUX channel you prefer

Done! :-)


Check the below Race footage from MewoFPV Cory Ibanez 1st place winner at the Nytfury VS Dolma Callout Race using the PyroDrone F4 OSD Flight Controller.

Straight gold. The US currency should be backed by this FC! (Cory Ibanez)
If you have V2.2 or V2.3 Boards please adjust the voltage scale in the Betaflight Power and Battery page as follows:


82 > V2.2
161 > V2.3



 

__________________________________________________________________________

Why buy from AirBlade UAV:

  • Fast and Affordable Shipping: We ship everyday from Vancouver, Canada using USPS (US orders), Canada Post (Canada & International orders), UPS and DHL. Learn more about our Shipping Policies.
  • Top Notch Customer Support: We put our customers’ interest ahead.
  • Complimentary Free Shipping: We offer free shipping for qualified US orders over $100 and qualified Canada orders over $250.
  • High Quality Products: Most products we carry are tested extensively by our team of experienced pilots. We only carry products we would personally use.
  • Latest Selection: We frequently refresh our stock selections to offer you the latest gears.
  • Support Community: We support local and international FPV communities and sponsor racing leagues where we see fit.

 

Shipping Weight: 30g